The Fluke TP82 Insulating Piercing Clips, 2mm (Red and Black) are made of stainless steel and pierce insulation on 14, 16 and 18 gauge wire. You can control needle depth to minimize insulation damage. These clips are essential for use under the hood or under the dash. Use them on fuel injectors or sensors while providing complete insulation to grounding, due to design. The Fluke TP81 also connects to banana jack leads.
View cart “Fluke DS703 FC Diagnostic Videoscope” has been added to your cart.
-10%
Previous product
Back to products Fluke TP81 Insulation Piercing Clip Set $132.00 $119.00
Excluding GST 10%
Next product
Fluke TP88 Rigid Back Probe Pins $42.00 $38.00
Excluding GST 10%
Fluke TP82 Insulation Piercing Clip Set
$132.00 $119.00Excluding GST 10%
- Banana jack accepts all DMM and banana jack leads
- Non-rotating banana jack prevents leads from tangling, allowing you to tighten/loosen clamp while still connected to the test lead
- For use with test leads with 2 mm probes
- Tested to 60 V DC
Available on backorder
SKU: 2149080 Categories: Accessories, Fluke Industrial
Related products
Fluke 190 Series II 200MHz 4 Channel ScopeMeter Oscilloscope
$7,486.00
Excluding GST 10%
Features
- Four independent isolated input channels
- 60, 100, 200 and 500 MHz bandwidths
- Sample rate: Up to 2.5 GS/s
- Sample rate resolution: Up to 400 ps
- Deep memory: 10,000 point per trace waveform capture
- CAT III 1000 V / CAT IV 600 V safety rating
- Seven hour, high performance Li-ion batteries
- Battery door for convenient battery access
- Isolated USB ports for memory devices and PC connectivity
Fluke 190 Series II 100MHz 4 Channel ScopeMeter Oscilloscope
Excluding GST 10%
Features
- Four independent isolated input channels
- 60, 100, 200 and 500 MHz bandwidths
- Sample rate: Up to 2.5 GS/s
- Sample rate resolution: Up to 400 ps
- Deep memory: 10,000 point per trace waveform capture
- CAT III 1000 V / CAT IV 600 V safety rating
- Seven hour, high performance Li-ion batteries
- Battery door for convenient battery access
- Isolated USB ports for memory devices and PC connectivity
Fluke 190 Series II 200MHz 2 Channel ScopeMeter Oscilloscope
$6,506.00
Excluding GST 10%
Features
- Four independent isolated input channels
- 60, 100, 200 and 500 MHz bandwidths
- Sample rate: Up to 2.5 GS/s
- Sample rate resolution: Up to 400 ps
- Deep memory: 10,000 point per trace waveform capture
- CAT III 1000 V / CAT IV 600 V safety rating
- Seven hour, high performance Li-ion batteries
- Battery door for convenient battery access
- Isolated USB ports for memory devices and PC connectivity
Fluke 810 Vibration Tester
$13,965.00
Excluding GST 10%
Features
- Plain-text diagnosis of standard faults:
- Unbalance
- Looseness
- Misalignment
- Bearing failures
- Fault severity (slight, moderate, serious, extreme)
- 200 rpm to 12000 rpm machine rotational speed range
- 5 Hz to 20 kHz Usable frequency bandwidth
- 2.56 kHz to 51.2 kHz sampling rate
- Lithium-ion, 14.8 V, 2.55 Ah battery
- 1/4 VGA, 320 × 240 color display
- Auto ranging
Fluke BT-520 Battery Analyzer
Excluding GST 10%
Key features
Fluke BT510 key features:
- Battery Voltage – During the internal resistance test, Fluke Battery Analyzers also measure the voltage of the battery under test
- Discharge Volts – The Discharge mode collects the voltage of each battery multiple times at a user defined interval during a discharge or load test. Users can calculate the time a battery takes to drop to the cut-off voltage and use this time to determine the capacity loss of the battery
- Ripple Voltage Test – Measures unwanted residual ac component of the rectified voltage in dc charging and inverter circuits. Allows users to test ac components in dc charging circuits and find one of the root causes of battery deterioration
- Meter and Sequence Modes – The Meter mode is used for a quick test or troubleshooting. In this mode you can save and read the readings in a measurement or time sequence. The Sequence mode is for maintenance tasks with multiple power systems and battery strings. Before a task starts, users can configure a profile for the task for data management and report generation
- Threshold and Warning – Users can configure a maximum of 10 sets of thresholds and receive a Pass/ Warning/ Fail indication after each measurement
- Intercell Strap Resistance Test and Data Management – Measures the resistance of the intercell connection between batteries in a string. Once the measurements are completed Fluke Battery Management Software version 1.0.69 can now report the strap resistance for a battery string or historical data over time.
- AutoHold – When AutoHold is turned on, a reading is captured when it remains stable for 1 second. The reading is then released when a new measurement starts
- AutoSave – When AutoSave is turned on, measured values are saved to internal memory automatically after an AutoHold reading is captured
Fluke 1736/B Three-Phase Power Loggers
Excluding GST 10%
Key features
- Versatile, three-phase Fluke Connect-compatible power logger for conducting basic energy and power quality studies
- Automatically captures and logs voltage, current, power, harmonics and associated power quality values.
- Provides the highest safety rating in the industry: 600 V CAT IV/1000 V CAT III rated for use at the service entrance and downstream
- Automatically logs all measured values and stores more than 20 separate logging sessions
Fluke 820-2 LED Stroboscope
Excluding GST 10%
Features
- 30 to 300,000 FPM (flashes per minute)
- 0.5 to 5000 Hz frequency range
- FPM or Hz frequency setting
- 0.02% accuracy
- Digital pulse width modulation
- Multi-line LCD display
- Operating temp: 32 to 113°F (0 to 45°C)
Fluke DS703 FC Diagnostic Videoscope
Excluding GST 10%
Key features
- High definition probe with dual-view camera
- Processing speeds that render a smooth, clear, consistent image
- 7” LCD screen for easy viewing
- Macro to micro zoom function
- Adjustable lighting to capture the best image
- Up is Up® technology for an appropriate orientation, regardless of the probe location
- Fluke Connect® allows you to save and share images directly from the diagnostic scope