-10%
Previous product 
Back to products Fluke i800 AC Current Clamp $668.00
Excluding GST 10%
Next product 
Fluke i3000s Flex AC Current Clamp $1,148.00
Excluding GST 10%
Fluke i200s AC Current Clamp
$506.00Excluding GST 10%
Features
- Take current readings without breaking the circuit
- 1.5% + 0.5A (48 to 65Hz) accuracy
- Switchable ranges
- 20A (100mV/A output)
- 200A (10mV/A output)
- 240A maximum non-destructive current
- 40Hz to 10kHz useable frequency
- 20mm maximum conductor diameter
- CAT III 600V safety rating
Available on backorder
Related products
Fluke 1555 FC w/IR3000FC 10 kV Insulation Tester with IR3000 FC Connector
Features
- Test voltages to up 10 kV and save time by trending on the spot only with Fluke Connect™
- CAT III 1000 V, CAT IV 600 V safety rating
- Warning function alerts the user that line voltage is present and gives the voltage reading up to 600 V AC or DC for increased user safety
- Selectable test voltages in 50 V steps from 250 V to 1000 V, and 100 V steps above 1000 V
- Measurements can be stored in up to 99 memory locations, with each location assigned a unique, user defined, label for easy recall
- Long battery life gives the user over 750 tests between charges
- Automatic calculation of Dielectric Absorption (DAR) and Polarization Index (PI) with no additional setup
- Guard system eliminates the effect of surface leakage current on high-resistance measurements
- Large digital/analog LCD for easy viewing
- Capacitance and leakage current measurement
- Ramp function for breakdown testing
- Resistance measurements up to 2 TΩ
- Timer settings up to 99 minutes for timed tests
- 3-year warranty
Fluke 1550C Digital Insulation Resistance Tester with IR3000 FC, 5kV
Features Fluke 1550C
- Quickly configure, start, and stop tests remotely, a safe distance away from any operating, energized equipment, using Fluke Connect® and a smartphone
- Real time trending gives you easy-to-see visual cues, rather than hard to read, rapidly changing values
- Automatic calculation of Dielectric Absorption (DAR) and Polarization Index (PI) with no additional setup
- Guard system eliminates the effect of surface leakage current on high-resistance measurements
- Selectable test voltages in 50 V steps from 250 to 1000 V, and 100 V steps above 1000 V
- CAT III 1000 V, CAT IV 600 V safety rating
- Warning function alerts the user that line voltage is present and gives the voltage reading up to 600 V AC or DC for increased user safety
- Measurements can be stored in up to 99 memory locations, with each location assigned a unique, user defined, label for easy recall
- Long battery life gives the user over 750 tests between charges
- Large digital/analog LCD for easy viewing
- Capacitance and leakage current measurement
- Ramp function for breakdown testing
- Resistance measurements up to 2 TΩ
- Timer settings up to 99 minutes for timed tests
Features Fluke IR3000FC Connector
- Fits over the IR port of your existing Fluke Tools
- Upgradeable by USB
- Immediately enables you to graph, save and share the tool’s reading with your team from your smart phone
Close
Fluke 435-II Three Phase Power Quality Analyzers
Key features
The Fluke 435-II products are designed for users who need to get to the solution of the power quality problem as quickly as possible so that they can minimize expensive downtime. The measurement process and display of data is optimized to get to the most important information as quickly as possible. Multiple parameters are measured simultaneously and displayed in formats that quickly describe overall power quality health while giving you the detailed information you need to make better maintenance decisions. Data can be quickly accessed as simple digital values, trend graphs that give you fast insight into changes over time, waveforms, phasor diagrams or analyzed and organized into tabular format such as the event data where the magnitude, duration and time stamping enable rapid correlation to the problems you are experiencing in your facility.
Energy loss Calculator—Calculate money lost to energy waste in terms of real dollars.
It’s a simple fact, poor power quality can have a big impact on the bottom line. The Fluke 435-II enables you to identify issues and measure energy loss giving you specific insight into the amount of loss in dollars associated things like effective power and with poor power quality characteristics such as reactive power, unbalance, distortion, or neutral current. The 435-II even offers users the flexibility to input cable length and cable diameter so you can calculate loss due to conductor sizing (Or use AUTO mode if you don’t know your cable specification) and enter up to four unique time-dependent daily rates (kWh) for more accurate calculations. Armed with this critical data users can easily justify the investment necessary to take countermeasures.
Close
Fluke 1663 Multifunction Installation Tester
Features
- 500V AC/DC voltage measurement TRMS
- 0.1V resolution & 3.3MΩ input impedance
- 660V RMS overload protection
- 20, 200, & 2000Ω auto-ranging continuity test
- 0.01, 0.1, & 1Ω resolution
- >4V open circuit voltage
- L-N, L-PE, N-PE inputs
- 50, 100, 250, 500, & 1000V insulation test voltages
- Test smooth DC sensitive RCDs (Type B/B+)
- 200 & 2000Ω earth resistance test
- 0.1 & 1Ω resolution
- 125Hz frequency & 25V output voltage
- On/Off switchable auto-start for RCD & Looptest
- Time & date (with optional FlukeView software)
- IP40 rated housing
- Complies with IEC/EN, UL, ANSI/ISA, & CAN/CSA
Fluke DS701 Diagnostic Videoscope
Key features
- High definition probe with dual-view camera
- Processing speeds that render a smooth, clear, consistent image
- 7” LCD screen for easy viewing
- Macro to micro zoom function
- Adjustable lighting to capture the best image
- Up is Up® technology for an appropriate orientation, regardless of the probe location
Fluke 1736/B Three-Phase Power Loggers
Key features
- Versatile, three-phase Fluke Connect-compatible power logger for conducting basic energy and power quality studies
- Automatically captures and logs voltage, current, power, harmonics and associated power quality values.
- Provides the highest safety rating in the industry: 600 V CAT IV/1000 V CAT III rated for use at the service entrance and downstream
- Automatically logs all measured values and stores more than 20 separate logging sessions
Fluke 6500-2 Portable Appliance Tester
Key features
Fluke Simplifies Portable Appliance Testing
- Dedicated key for each test for ‘one-touch’ testing
- Pre-set pass/fail levels to save time
- Large backlit display for easy reading
- Single mains socket for appliance connection
- Separate IEC socket for easy mains/extension lead testing
- Detachable test leads for quick field replacement
- Integral carrying handle
- USB port for data transfer
Fluke 123B Industrial ScopeMeter® Hand-Held Oscilloscope, 20 MHz
Features
- Dual-input digital oscilloscope and multimeter
- 20 MHz oscilloscope bandwidth
- Two 5000-count True RMS digital multimeters
- Connect-and-View™ trigger simplicity for hands-off operation
- IntellaSet™ technology automatically and intelligently adjusts numerical readout based on the measured signal
- Dual-input waveform and meter reading recorder for trending data over extended periods
- Recorder Event Detect captures elusive intermittent signals on repetitive waveforms up to 4 kHz
- Shielded test leads for oscilloscope, resistance and continuity measurements
- Resistance, continuity, diode and capacitance meter measurements
- Power measurements (W, VA, VAR, PF, DPF, Hz)
- Voltage, current and power harmonics
- Check Industrial networks with BusHealth physical layer tests against defined reference levels
- Save or recall data and instrument setups
- Store instrument setups defined by a test sequence for routine maintenance or most often used test procedures
- External optically isolated USB interface to transfer, archive and analyze scope or meter data
- Optional WiFi adapter connected to internal USB port to wirelessly transfer information to the PC, laptop or Fluke Connect® mobile app
- FlukeView® ScopeMeter® Software for Windows®
- Rugged design to withstand 3g Vibration, 30g shock, and rated IP51 according to EN/IEC60529
- Highest safety rating in the industry: safety rated for CAT IV 600 V
